 |
> PLC AUTOMATION SYSTEM> Power Supply,Thumbwheel Modules, Special Modules |
 |
|
 |
| Spec.
/ Model |
FBs-4PT |
FBs-ATC2 |
FBs-1LC |
FBs-AXC2 |
| Features |
4 channels,
16-bit potential
meter input module
(Impedance range: 1K~10K Ω) |
2 channels,
auto. tuning
temperature control module
with 0.1°C resolution |
1 channel, load
cell module
with 20-bit resolution |
2 axes, with
linear uncircular
interpolation motion control
module |
| Wiring
mechanism |
7.62
mm terminal block |
| Dimension |
Figure
4 |
|
|
|
|
| ^ TOP |
 |
Power Supplies for Expansion Modules |
|
|
|
 |
| Spec.
/ Model |
FBs-EPOW |
FBs-EPOW-D |
Capacity
of output
power |
24VDC
Bus power |
400mA
|
400mA |
| 24VDC
Bus power |
250mA |
165mA |
| Sensor
power |
250mA |
165mA |
| Max.
power consumption |
100 ~
240VAC
-15%/+10%, 21W |
15VDC/24VDC
-15%/+20%, 15W |
| Wiring
mechanism |
Wiring
mechanism 7.62 mm terminal block |
| Dimension |
Figure
4 |
|
|
| ^ TOP |
|
Thumbwheel Switch Input Module |
|
|
|
 |
| Spec.
/ Model |
FBs-32DGI |
| Refresh
time for input |
10mS max. |
| Input
capability |
8 words (32 digits/128
individual points) |
| Input
method |
1/8 duty multiplexing
input scan |
| Wiring
mechanism |
30 pins header with
latch |
| Dimension |
Figure 6 |
|
|
| ^ TOP |
|
7/16-segment LED display modules |
|
|
|
 |
| Spec.
/ Model |
FBs-7SG1 |
FBs-7SG2 |
| Display
mode |
Decoding
display |
4
bits to represent a character.
It can display 16 kinds of pre-decoded character including
0 ~ 9, –, H, E, c, t and all blank |
| Non-decoding
display |
Each
segment controlled by 1 individual bit |
| Display
number of character or points of LED |
8 (4*) characters
or 64 points individual LED |
16 (8*) characters
or 128 points individual LED |
| Refresh
time for display |
10mS
max. |
LED
driving
specification |
Driving
current |
40mA
/segment |
| Display
method |
1/8
duty multiplexing display |
Driving
voltage |
Low
voltage |
5VDC
(can be 10% up) |
| High
voltage |
7.5V,
10V, 12.5V selectable (can be 10% up) |
| Fine
tune of voltage drop |
0.6V,
1.2V, 1.8V selectable |
| Over
voltage driving indication |
Each
channel has individual Over Voltage (O.V.) driving LED
indication |
| Isolation
method |
Transformer
(power) and photocouple (signal) isolation |
| Power
consumption |
24VDC –15%/+20%,static consumption is 2VA max.,
dynamic current is increased according to display. |
| Wiring
mechanism |
16
pins flat cable, 2.54mm header connector |
| Dimension |
Figure
4 |
|
|
| ^ TOP |
